濟南裝載機配件潤滑油如何選用？

濟南裝載機配件http://www.ts0775.cn/機油的不足有可能會導致潤滑效果差，機械的損壞率變大甚至有可能會引起事故的發生，但事實上油量過多不僅不會使得機械在傳動過程中的摩擦力減小，甚至還會使曲軸的轉動阻力變大，使得動力消耗的更大，并且在轉動過程中容易出現氣泡，使得潤滑效果不良。在選用潤滑劑的時候要選用黏度較小的的潤滑劑，因?yàn)闈?rùn)滑劑的黏度選的過高的話會使機油的油泵疏松性能變差，流量變小，使得潤滑性，散熱性變差，發生一些不必要的故障。
Jinan loader accessories insufficient oil may cause poor lubrication, mechanical failure rate increases may even cause accidents, but in fact does not make too much oil in the transmission process of mechanical friction reduction small, even the crankshaft rotational resistance becomes large, so that more power consumption, and prone to air bubbles during rotation, so that poor lubrication effect. When the lubricant in the selection to choose a small viscosity of the lubricant, since the lubricant viscosity is too high, then selection of an oil pump will loose oil deterioration, the flow becomes small, so that lubrication, heat deterioration occurs some unnecessary failures.
  
現在的潤滑油都根據不同的情況添加了不同程度的添加劑，有的時候機油在使用時間不久之后就開始變黑，但是不要以為這是機油變質需要更換了，由于不同的狀況，加入了不同的添加劑，使得不能從單一的角度來判斷是否機油變質，需要在多種情景的分析之下，在作出是否需要更換的決定。
Now oil is added according to different situations with varying degrees of additives, sometimes in time shortly after the oil began to darken, but do not think this is the need to replace the oil deterioration, due to the different conditions, adding a different additives, making it impossible from a single perspective to determine whether oil deterioration, require analysis under a variety of scenarios, the decision whether or not to be replaced.
   
濟南裝載機配件http://www.ts0775.cn/的養護是非常重要的，養護的好使用的時間就一定會增長，這樣也能盡量的減少了更換設備所需要投入的成本。
Jinan loader accessories conservation is very important, a good time to use conservation will certainly grow, so too can try to reduce the need to invest in equipment replacement costs.